A continuación listamos los errores presentes en el libro de mantenimiento de los plotters Epson SureColor SC-T3000/T5000/T7000 y que iremos actualizando con nuestras recomendaciones en base a experiencias propias y con clientes.
Con esta «base de datos», queremos ayudar a usuarios de impresoras gran formato a solucionar cualquier problema o incidencia que surga con su máquina. Aunque en muchos casos la avería es solucionable por el usuario, en otros casos será inevitable la presencia de un técnico especializado. Por ello no podemos dejar de advertir que cualquier intervención en la impresora conllevará un riesgo que el usuario deberá asumir.
| 0001 | NMI error CPU detects NMI |
Replace the MAIN BOARD. |
| 0002 | System error | Replace the MAIN BOARD. |
| 1101 | CR life error CR scan pass counter has reached the specified value. (which means the INK TUBES have reached the end of their service life.) |
Replace the INK TUBES and reset the counter of the INK TUBE . |
| 1125 | CR HP detection error The CR HP SENSOR cannot detect the CR UNIT. Or the CR UNIT cannot detect the touching surface for the home position setting, so the home position cannot be set. • CR HP SENSOR failure • False detection of the home due to paper jam or any other obstacle • Misreading of CR SCALE • CR Lock is damaged. |
1. Replace the CR HP SENSOR. 2. Re-install the CR ENCODER. If it is faulty, replace it. 3. Clean the CR SCALE using ethanol. 4. Replace the CR SCALE. 5. Replace the CR Lock . |
| 1138 | Over current error Connection failure of the CR MOTOR or the CR ENCODER. • The number of occurrences of overcurrent to the CR MOTOR has reached a predetermined limit. • Irregular load • CR ENCODER failure • CR MOTOR failure |
1. Replace the CR ENCODER. 2. Replace the CR MOTOR. |
| 1139 | Oscillation error The control terminal (Vre terminal) of the CR MOTOR driver has shorted out. |
1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| 113A | Overload error Overcurrent to the CR MOTOR was detected. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
1. Re-install the CR UNIT. 2. Replace the CR ENCODER. 3. Replace the CR MOTOR. |
| 113B | Over speed error The CR MOTOR was driven at a speed faster than a predetermined one during deceleration. • Irregular load • CR ENCODER failure • SUB BOARD is damaged. • CR MOTOR driver failure |
1. Replace the CR ENCODER. 2. Replace the SUB BOARD. 3. Replace the MAIN BOARD. |
| 113C | Reversing error The number of occurrences of reversing the CR MOTOR has reached a predetermined limit. • The polarity of CR ENCODER cable is opposite. • The polarity of CR MOTOR cable is opposite. • Slipping of the teeth of CR TIMING BELT • CR ENCODER failure |
1. Adjust the tension of the CR TIMING BELT. 2. Replace the CR ENCODER. |
| 113D | Driving time-out error Abnormally-long driving duration of the CR MOTOR was detected. • Irregular load • Firmware becomes out of control. |
Replace the MAIN BOARD. |
| 113E | Velocity deviation error The CR MOTOR was driven at a speed abnormally faster than a predetermined one during acceleration or deceleration. • Irregular load • CR ENCODER failure • CR MOTOR failure • SUB BOARD is damaged. • CR MOTOR driver failure |
1. Replace the CR ENCODER. 2. Replace the CR MOTOR. 3. Replace the SUB BOARD. 4. Replace the MAIN BOARD. |
| 113F | Lock error The CR MOTOR was driven at a speed abnormally slower than a predetermined one during operation. • CR ENCODER cable is damaged. • CR MOTOR cable is damaged. • Irregular load • CR ENCODER failure • CR MOTOR failure |
1. Replace the CR ENCODER. 2. Replace the CR MOTOR. |
| 1219 | Oscillation error The control terminal (Vre terminal) of the PF MOTOR driver has shorted out. |
1. Remove the foreign material. 2. If the error still occurs, replace the MAIN BOARD. |
| 122A | Overload error Overcurrent to the PF MOTOR was detected. • PF ENCODER cable is damaged. • PF MOTOR cable is damaged. • Irregular load • PF ENCODER failure • PF MOTOR failure |
1. Replace the PF ENCODER. 2. Replace the MAIN BOARD. |
| 122B | Over speed error The PF MOTOR was driven at a speed faster than a predetermined one during deceleration. • PF irregular load • PF ENCODER failure • SUB-B BOARD is damaged. • PF MOTOR driver failure |
1. Replace the PF ENCODER. 2. Replace the SUB-B BOARD. 3. Replace the MAIN BOARD. |
| 154A | Overcurrent to the cutter motor was detected. – Cutter motor encoder cable is damaged. – Cutter motor cable is damaged. – Irregular load – Cutter motor encoder failure – Cutter motor failure |
Replace the cutter motor/cutter motor encoder (CUTTER UNIT). Consejo Arkiplot: Se recomienda revisar y limpiar -con cuidado- la unidad de corte. Revisar que el mecanismo no esté obstruido. |